Announcement

Collapse

Announcement

Welcome to the NEW iPad Rehab Forum! Everyone is welcome to read posts and learn for free. If you'd like to post your own question on the forum, please click "register" above or go here: http://forum.mendonipadrehab.com/register to enroll as a paid subscriber for $29/mo for unlimited access to our forum support and private signature failure section.
See more
See less

iPhone 7 plus received for a screen replacement

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Jessa_the_Professa
    replied
    Are you sure Touch ID was working previously? It will be difficult to troubleshoot because each home button is unique to the device and can’t just be swapped. You would need to have a known good device to confirm that this is the screen the other possibility is software or the crease in the flex.

    Leave a comment:


  • eDigitCom
    commented on 's reply
    Did a Hard reset Jessa but not solve Thanks for input

  • eDigitCom
    replied
    Thanks Jessa very much

    But have one of these customer that thinks I damaged her phone and has spread the word also to a least one other person that I damaged it without any proof at all

    Leave a comment:


  • Jessa_the_Professa
    replied
    Sometimes a hard reset (not restore or update, just reset) is required to get a phone to recognize fingerprint sensor.

    Leave a comment:


  • eDigitCom
    replied
    Error

    unable to complete touch id setup please go back and try again

    Anyone come across this error when trying to create a new fingerprint touch


    I search on the internet it shows it is a fairly common fault

    IOS at top rev of 11.4.1


    Any solutions or ideas

    Is it a hardware or a software problem??

    Thanks




    Leave a comment:


  • eDigitCom
    replied
    Just tried another screen with just the home button attached and it powers up normally with the Home button working but cannot create a new fingerprint Touch ID has it fails to do so

    It does not give any error on power up about the touch ID failing but I cannot create a new fingerprint touch ID in settings

    Does the finger print created by the customer still work I will have to wait and see


    Just to proof it was the screen or something else I remove all the parts from the other screen and just attach the Home Button and see the outcome. The fault was still there causing the Home Button issues

    So the screen is the problem

    But what is preventing it to create a new fingerprint ID is now the issue remaining??

    Would love now to have a know good working iPhone 7 plus this would really tell if again there is a screen issue causing it not to create a fingerprint id
    Last edited by eDigitCom; 07-13-2018, 06:45 PM.

    Leave a comment:


  • eDigitCom
    replied
    Jessa_the_Professa

    ". In the future, even with a severely cracked screen you can at least test for long boot up time (and you should!) because you want to show customer if this phone may have an audio ic fault that they are unaware of"

    This is not possible at present I take it Jessa. It would be great has you could then test it before replacing the screen

    Are you working on this Jessa?? Or is it the type of graph you get on power up
    Last edited by eDigitCom; 07-13-2018, 06:49 PM.

    Leave a comment:


  • eDigitCom
    replied
    Jessa_the_Professa "You seem to have a significant crease in the home button near the connector--that could potentially be a problem"

    I see the crease Jessa but this is normal so the cable connector is able to slot into the logic board cable on the screen If you notice from the video this is the case It will not attach if the cable is straight

    This is the way it was when removed from the Screen cable when you flip it off it


    I not think it is an Audio IC issue myself the only symptom of an Audio IC issue it has is the long boot time. which is it takes exactly 5 min to boot


    So on boot up is it possible the CPU is looking for the home button and eventual gives up when it cannot detect it??
    Last edited by eDigitCom; 07-13-2018, 04:54 PM.

    Leave a comment:


  • Jessa_the_Professa
    commented on 's reply
    You seem to have a significant crease in the home button near the connector--that could potentially be a problem, but we can't say for sure. You could check in diode mode to see if you have any OL. There are a lot of home button measurements in our It Takes Village section. In the future, even with a severely cracked screen you can at least test for long boot up time (and you should!) because you want to show customer if this phone may have an audio ic fault that they are unaware of.
    I would rule out long flex or just bad screen and bad fcam assembly which can all also cause the same thing. Home button software does not seem to be a failure point.

  • eDigitCom
    replied
    Has I been aware how the Home Button and Logic Board communicates is the code build into the Home Button and the Logic board,

    If for example the code in the Home Button was corrupt they would not be able to communicate.

    Could this code be corrupt by a fall ??


    In my view it could

    Thanks Jessa
    Last edited by eDigitCom; 07-13-2018, 02:01 PM.

    Leave a comment:


  • eDigitCom
    replied
    I am at present replacing the screen with another just in case the cable on the screen going to the logic board itself is faulty. I do not have an know working iPhone 7 plus screen has have not another iPhone 7 plus working correctly

    Leave a comment:


  • eDigitCom
    replied
    Close up of connector

    Leave a comment:


  • eDigitCom
    replied
    Jessa I examined the Home Button Flex and connector under a micro-scope and there is no damage done to the flex. I attach photos + close up image of the damaged screen

    To remove the home button from the front of the screen (side opposite to the flex cable) I used a very small amount of heat until the flex cable just began to lift.slowly removing the flex cable and then outputting the button through its button hole

    Real care was done removing it Jessa

    You need to get a slight movement before removing them has otherwise you are going to tear the flex

    I have also done 3 iPhone 7 and one 7 plus using the exact same procedure and all worked fine after


    Here is a video I found on the internet which shows how to remove the Home Button This shows the same procedure I went about removing it He starts to remove the Home Button at 12.38 min

    https://www.youtube.com/watch?v=9eQiFPzC7Vk


    Thanks Jessa

    PS The Home button could not be tested before the screen replacement due to the damage done to the screen
    Last edited by eDigitCom; 07-13-2018, 12:23 PM.

    Leave a comment:


  • Jessa_the_Professa
    replied
    This sounds like you tore the home button flex. A phone takes a long time to boot when it doesn't have the native home button and flex tearing is common. This is not audio ic if there are no audio symptoms. Look under the microscope for a teeeeeeny tiny microscopic tear at the home button flex, or a puncture etc. Or just tell us how did you get the home flex off--did you use a little bit of heat?

    Leave a comment:


  • eDigitCom
    started a topic iPhone 7 plus received for a screen replacement

    iPhone 7 plus received for a screen replacement

    iPhone 7 plus received for a screen replacement

    The screen was shattered so I could not get access to the phone before replacing the screen to test the functions on the phone


    Once the new screen was fitted and all parts from its original screen to its replacement it took the phone five minutes to power up staying on the apple logo
    • Once it does power up the Home button and the touch ID do not work (greyed out in settings)
    • The iPhone showed the incorrect date and time

    All other functions on the phone worked fine including camera, voice menu etc
    • I corrected the date and time which did not solve any of the two issues
    • The iPhone needed a software update. Thinking it may have needed the software update to solve the issues I updated the software - Did not solve the problems
    • I removed the Proximity Cable but still took the 5 minutes to power up and did nothing to solve the Home Button problem
    Unfortunately, I do not have a good iPhone 7 plus too make sure it is not a parts problem

    The iPhone in now in the condition that it takes five minutes to power up and once powered up the Home Button and the Touch ID do not function



    Any input where the issue (s) may be ??? and next step(s)


    In Jessa training video on iPhone 7 a long boot time of 3 to 5 minutes may point to an Audio IC issue?? Would the Home Button be effected also from an AUDIO IC problem??



    https://www.youtube.com/watch?v=4Wmm_wqQnJc&t=3894s

    Maybe the long boot loop is due to it looking for the HOME Button.??? I checked the home button connector a few times and any damage to the cable but noting stood out

    Thanks

    Jerry
    Last edited by eDigitCom; 07-12-2018, 05:29 PM.
Working...
X